Nothing here is a service order or a booking. The path below describes what happens when a reader sends a question, a correction or a note about a technique we have covered, and what you can reasonably expect from that exchange.
Questions about how the magazine is put together sit on the company page, and practical help with the site itself is collected under support.
The five core subjects on this page describe documented hand and repair technique. They are not a service list, a course catalogue or a promise of a particular result. The notes below settle the readings that come up most often when readers write in.
Hand-plane flattening, grit selection, drill specification reading, floorboard repair and chisel sharpening are written up as methods you carry out yourself. Nothing on this page is offered as paid work, a package or a booking.
If a guide names a tool, it is because the method needs it, not because anything is for sale.Every subject here ends with a check: a straightedge across the board, a fingertip along the edge, a test screw before the full run. That check is the stopping point. Where a guide says a surface is flat enough or an edge is sharp enough, it means enough for the next step, not perfect.
Results depend on the timber, the tool condition and the care taken, so no outcome is guaranteed.You will not find rates, schedules or response times attached to these subjects, because none exist to publish. The editorial team answers questions about method and corrections to published guides through the contact page, and that is the whole of the practical offer.
Questions about a specific wall, floor or door are read as questions, not as orders.When a drill sheet is explained, the aim is to show what torque, clutch settings and chuck type mean in use. Two tools with the same voltage can behave differently, and the text says so rather than declaring a winner. No brand is endorsed and no purchase is recommended.
Compare the numbers against the work you actually do, then decide.Fasteners driven blind into a floor can meet pipes or cables. Solvent and dust from sanding need ventilation and the right mask. Where a guide carries a safety note, treat it as a condition of doing the job, not an optional remark at the end.
If a check cannot be made safely, the honest answer is to stop and reassess.Where a text describes a rough plank, a painted door or a squeaking board, it is illustrating a typical situation so the steps have something concrete to work on. It is not a record of a particular house, customer or finished project.
Read them as worked examples, then adapt the checks to your own material.Still unsure how a subject applies to your situation? Write to info@rumnade.com or use the contact page. The address for correspondence is Friedrichstraße 68, 10117 Berlin, Germany.
Every subject on this page is taught the same way: name the tool, describe the check, and say where to stop. Nothing here is a package or a promise of a finished result. It is a record of how a method is verified before it goes into a guide.
When a technique is written up, the editor first works through it on scrap material and notes the points where a reader could go wrong. Those notes become the checks in the article. If a step depends on a condition we cannot confirm, such as the moisture in a particular board or the pipe route under a floor, the guide says so instead of guessing.
A guide lists the plane, stone, grit or driver it assumes, including the size and type where that changes the outcome. If a cheaper substitute works for the same check, the text says which one and why. Readers should be able to look at their own bench and decide whether they can start today.
A winding stick, a straightedge, a square or a test cut tells you whether the last pass did what it should. The check comes before the next step, not after the whole job. That order is what separates a repeatable method from a hopeful shortcut, and it is the part we refuse to compress.
Flat enough, square enough, sharp enough: every guide defines the moment to put the tool down. Without that line, readers keep sanding through a veneer or honing past a good edge. Where a stopping point depends on the material in front of you, the text describes what to look and feel for rather than giving a number that may not fit.
Hidden pipes under a floor, paint of unknown age, a board with a crack running through it: these change the advice. We keep such conditions in the body of the text instead of a footnote. Where a job needs a trade or a second pair of eyes, the guide says so and does not pretend the method covers it.
If a reader spots a step that does not hold up, the editorial team reviews it against the original checks and revises the text. Send a note through the contact page with the subject and the step in question. We do not publish ratings, testimonials or claims about outcomes, because the useful evidence here is the method itself.
This site stores your answer in your browser's local storage so the notice stays closed on later visits. Accepting or declining only records that choice and does not affect the contact form. You can clear it any time in your browser settings.